Step 6 of 8
NISSAFORS trolley step 6 of 8: Fit the second side frame, turn over and start 8 screws
Set the second side frame on top of the three trays, turn the trolley over onto it so the new frame rests flat on the rug, and start the remaining 8 screws (190419) with the hex key (190094)—4 in the deep bottom tray and 2 in each shallow tray—again leaving a small gap under each head.
- 1× Side frame
- 8× Screw
190419
Tools: Hex key (190094, in the box)
All 8 steps
- 1 Slide the short end rims onto the three mesh bottoms
- 2 Lock the short end rims with 6 snap sleeves and pins
- 3 Fit the long side rims and click the four corners home
- 4 Lock the long side rims with 12 snap sleeves and pins
- 5 Stand the three trays on the first side frame and start 8 screws common mistake
- 6 Fit the second side frame, turn over and start 8 screws
- 7 Tighten all 16 frame screws firmly
- 8 Click in the 4 castors and stand the trolley upright
00Overall
The outer size is IKEA's published size.
01Elevations
Drawn from our 3D model, to scale. Point at a part to find it in the list below; click it to jump there.
02Parts / cut list
| Part | Name | Qty | T | W | L | Material |
|---|---|---|---|---|---|---|
| A | Mesh bottom3 × 292 × 470 mm | ×3 | 3 mm | 292 mm | 470 mm | Steel, epoxy/polyester powder coating |
| B | Deep end rim2 × 88 × 292 mm | ×2 | 2 mm | 88 mm | 292 mm | Steel, epoxy/polyester powder coating |
| C | Deep side rim2 × 88 × 471 mm | ×2 | 2 mm | 88 mm | 471 mm | Steel, epoxy/polyester powder coating |
| D | Shallow end rim2 × 46 × 292 mm | ×4 | 2 mm | 46 mm | 292 mm | Steel, epoxy/polyester powder coating |
| E | Shallow side rim2 × 46 × 471 mm | ×4 | 2 mm | 46 mm | 471 mm | Steel, epoxy/polyester powder coating |
| F | Side frame16 × 300 × 765 mm | ×2 | 16 mm | 300 mm | 765 mm | Steel, epoxy/polyester powder coating |
The parts' sizes are our 3D model's own estimates: close, not measured. The overall dimensions, load limits and spare-part numbers are IKEA’s; the tube section, tray rim heights and hole positions are our own estimates from the product photos, so they are close, not measured. IKEA publishes only the outer size.
03Tools & materials
| Tools | ||
|---|---|---|
| Hex keyIn the box: a 3 mm L-shaped ball-end hex key (190094, 80 × 30 mm) that drives and tightens the 16 frame screws (190419). | In the box 190094 | |
| Materials | ||
| Steel, epoxy/polyester powder coating | ABCDEF | |
04Hardware
| ×16 | Screwit may be 190419 or 10051663 | 190419 | M5 × 8 mm, 11 mm head | Black steel |
| ×18 | Snap sleevecolour variants use 10050916, 10049406, 10090669, 10116053, 10116025, 10125545 or 10166525 | 10005471 | Ø 5.2 × 5.6 mm, 7.7 mm flange | Black plastic |
| ×18 | Snap pincolour variants use 10050917, 10049407, 10090656, 10116045, 10116026, 10125539 or 10166526 | 10005485 | Ø 3 × 6 mm, 10 mm head | Black polycarbonate |
| ×4 | Castor | 10054852 | Ø 50 mm wheel, Ø 7 mm stem | Black plastic, synthetic rubber, steel stem |
Questions
What tools do I need to assemble the NISSAFORS trolley?
No extra tools are needed. The 3 mm L-shaped hex key (190094) for the 16 frame screws is included in the box, and the 18 snap sleeves, 18 snap pins and 4 castors push in by hand.
Why does the deep bottom tray take 8 screws while the other two trays take 4?
The deep bottom tray uses two screws at each corner (4 per side frame, 8 in all) to brace the two U-shaped side frames and keep the trolley square, while the middle and top shallow trays use one screw at each corner.
Why shouldn’t I tighten the screws all the way in steps 5 and 6?
Leaving a small gap under the screw heads while you attach the first and second side frames lets all three trays settle square so every hole lines up. Once all 16 screws (190419) are started, tighten them firmly in step 7.
How much weight can the NISSAFORS trolley hold?
IKEA rates the trolley for up to 7 kg per tier and 21 kg in total.
Safety
IKEA gives a maximum load of 7 kg per tier and 21 kg in all. For indoor use (and bathroom use in a splash- and water-free area), tested to EN 16121:2023 (Test Parameter 1, General Use), and not approved for food contact. Re-tighten the screws when necessary.
About this guide
This is an independent 3D engineering guide modeled from physical hardware specifications and standard fastener part numbers so you can identify your pieces before building. The outer size, 50.5 × 30 × 83 cm, is IKEA's published size. The overall dimensions, load limits and spare-part numbers are IKEA’s; the tube section, tray rim heights and hole positions are our own estimates from the product photos, so they are close, not measured. The 3D runs faster than real hands do.
IKEA gives a maximum load of 7 kg per tier and 21 kg in all.
The manufacturer's instructions are on IKEA's product page (PDF). If something here differs from the manual in your box, follow the manual.
The 3D models, drawings and text are our own. IKEA and NISSAFORS are named only to say which product this guide is for.