Step 26 of 36

VIHALS sideboard step 26 of 36: Screw four cam bolts into the back of each drawer front

Lay the two drawer fronts face down on the rug. With a cross-head screwdriver, screw 4 cam bolts (130449) into the two pairs of holes near the left and right ends of each drawer front until their shoulders sit flush.

2× Drawer front
8× Cam bolt 130449

Tools: Cross-head screwdriver

All 36 steps

00Overall

W1400 mm

D370 mm

H750 mm

The outer size is IKEA's published size.

01Elevations

Front

Right side

Drawn from our 3D model, to scale. Point at a part to find it in the list below; click it to jump there.

02Parts / cut list

Part	Name	Qty	T	W	L	Material
Frame
A	Left side panelForms the left end of the sideboard. Its factory-fitted wedge dowels drop into the keyhole slots in the bottom and top panels and slide forward to lock.16 × 354 × 670 mm	×1	16 mm	354 mm	670 mm	Particleboard, acrylic paint, plastic edging
B	PartitionDivides the sideboard into two bays. Both of its faces carry a drawer runner at the top, two door hinges below, and two shelf pins in the middle.16 × 342 × 670 mm	×1	16 mm	342 mm	670 mm	Particleboard, acrylic paint, plastic edging
C	Right side panelForms the right end of the sideboard, mirroring the left side panel.16 × 354 × 670 mm	×1	16 mm	354 mm	670 mm	Particleboard, acrylic paint, plastic edging
D	Bottom panelThe full-width base of the cabinet. The six block feet pass through its slots to the floor while the sides and partition click into its keyhole slots.18 × 370 × 1400 mm	×1	18 mm	370 mm	1400 mm	Particleboard, acrylic paint, plastic edging
E	Lower back panelThick particleboard back panel spanning the lower half of both bays. It slides down the grooves in the sides onto the four dowels in the bottom panel.12 × 335 × 1368 mm	×1	12 mm	335 mm	1368 mm	Particleboard, paper foil
F	Upper back panelSpans the upper half of both bays, resting on the four dowels in the lower back panel. Its top corner notches leave room for the wall brackets.12 × 335 × 1368 mm	×1	12 mm	335 mm	1368 mm	Particleboard, paper foil
G	Top panelThe 140 × 37 cm top surface. Lowered onto the six wedge dowels at the top of the sides and partition and pushed toward the back until it clicks.18 × 370 × 1400 mm	×1	18 mm	370 mm	1400 mm	Particleboard, acrylic paint, paper foil, plastic edging
H	Left shelfAdjustable shelf in the left bay, resting on four plastic shelf supports (max load 18 kg).16 × 320 × 672 mm	×1	16 mm	320 mm	672 mm	Particleboard, acrylic paint, plastic edging
J	Right shelfAdjustable shelf in the right bay, resting on four plastic shelf supports (max load 18 kg).16 × 320 × 672 mm	×1	16 mm	320 mm	672 mm	Particleboard, acrylic paint, plastic edging
K	Left outer doorOne of the four doors (two per bay). Each hangs on two hinges with built-in mounting screws and takes a white aluminium lip handle along its top edge.16 × 344 × 468 mm	×1	16 mm	344 mm	468 mm	Particleboard, acrylic paint, plastic edging
L	Left inner doorOne of the four doors (two per bay). Each hangs on two hinges with built-in mounting screws and takes a white aluminium lip handle along its top edge.16 × 344 × 468 mm	×1	16 mm	344 mm	468 mm	Particleboard, acrylic paint, plastic edging
M	Right inner doorOne of the four doors (two per bay). Each hangs on two hinges with built-in mounting screws and takes a white aluminium lip handle along its top edge.16 × 344 × 468 mm	×1	16 mm	344 mm	468 mm	Particleboard, acrylic paint, plastic edging
N	Right outer doorOne of the four doors (two per bay). Each hangs on two hinges with built-in mounting screws and takes a white aluminium lip handle along its top edge.16 × 344 × 468 mm	×1	16 mm	344 mm	468 mm	Particleboard, acrylic paint, plastic edging
Drawers
P	Drawer front16 × 196 × 692 mm	×2	16 mm	196 mm	692 mm	Particleboard, acrylic paint, plastic edging
Q	Drawer side12 × 120 × 300 mm	×4	12 mm	120 mm	300 mm	Particleboard, paper foil
R	Drawer bottomWhite-painted fibreboard bottom that slides along the grooves of the drawer sides into the groove in the drawer front.3 × 288 × 620 mm	×2	3 mm	288 mm	620 mm	Fibreboard, acrylic paint
S	Drawer backCloses the back of the drawer box above the bottom panel and locks onto the four plastic dowels with four cam locks.12 × 105 × 620 mm	×2	12 mm	105 mm	620 mm	Particleboard, paper foil

The parts' sizes are our 3D model's own estimates: close, not measured. The outer size and max. shelf load are IKEA’s. Board thicknesses, drawer sizes and hole positions are our own estimates. IKEA publishes only the outer size.

03Tools & materials

Tools
	Hex keyComes in the box. Drives the four lock screws (10077982) into the back of the bottom and top panels.	In the box `100092`
	Cross-head screwdriverDrives the runner screws (10048881, 146114), the hinge screws, the cam bolts (130449), the bracket screws (105811, 109049) and the wall screws (109048).	You need it
	Flat screwdriverTurns the 16 cam locks (119030) in the sides and backs of the two drawers.	You need it
	HammerTaps in the two wall plugs (121714) and the eight plastic drawer dowels (145718).	You need it
	PencilMarks the wall through the slots in the two wall brackets.	You need it
	Electric drill (8 mm bit)Drills the two 8 mm holes in the wall for the wall plugs (121714).	You need it
Materials
	Particleboard, acrylic paint, plastic edging	ABCDHJKLMNP
	Particleboard, paper foil	EFQS
	Particleboard, acrylic paint, paper foil, plastic edging	G
	Fibreboard, acrylic paint	R

Not in the box: 2 wall screws and 2 wall plugs that suit your wall.

04Hardware

×12	Euro screw	`10048881`	13 × 5 mm	Zinc-plated steel
×8	Drawer runnerfour cabinet halves and four drawer halves	`10060247`	300 mm long	Epoxy-coated steel, nylon roller
×8	Hinge	`10071303`		Nickel-plated steel
×6	Block foot	`10061178`		White plastic
×8	Wooden dowel	`101345`	30 × 8 mm	Beech
×4	Snap sleeve	`10050769`	32 × 10.2 mm	White polyamide
×4	Snap pin	`10050771`	33.5 × 4.6 mm	White polyamide
×4	Lock screw	`10077982`	33 × 7 mm	Zinc-plated steel
×2	Corner bracket	`10003780`	68 × 36 × 2 mm	Steel
×4	Euro screw	`105811`	9 × 6 mm	Zinc-plated steel
×2	Wall bracket	`106989`		Galvanized steel
×2	Bracket screw	`109049`		Zinc-plated steel
×4	Washer	`100823`		Zinc-plated steel
×2	Wall plug	`121714`		Grey plastic
×2	Wall screw	`109048`	60 mm long	Zinc-plated steel
×8	Shelf support	`10051660`		White plastic
×6	Handle	`10071494`	38.5 × 35 × 18 mm	White aluminium
×20	Short Euro screw	`146114`	10 × 5 mm	Zinc-plated steel
×4	Door bumper	`102384`	12 × 3 mm	Clear plastic (EVA)
×8	Cam bolt	`130449`	30.3 × 6.5 mm	Zinc-plated steel
×16	Cam lock	`119030`	15 mm across	Composite
×2	Drawer bottom holder	`10040242`		Zinc-plated steel
×8	Drawer dowel	`145718`	42.1 × 7.6 mm	White polyamide

Questions

Why does the VIHALS sideboard have two different short Euro screws (10048881 and 146114)?

The 12 slightly longer pan-head screws (10048881, 13 mm) attach the four cabinet drawer runners to the thick side panels and partition in steps 1–3. The 20 shorter screws (146114, 10 mm) fasten the six lip handles (10071494) and the four drawer-side runners so they do not poke through the 16 mm fronts or 12 mm drawer sides.

How do the wedge dowels on the sides and partition lock into the bottom and top panels?

The side panels and partition come with factory-fitted ribbed wedge dowels on their top and bottom ends. Drop the dowels into the wide ends of the keyhole slots in the bottom panel (steps 6–8) and push each upright toward the front until it clicks; then lower the top panel onto the upper dowels (step 14), push it toward the back until it clicks, and secure both panels at the back with the four hex lock screws (10077982) in step 15.

How many doors and shelves does the 140×37×75 cm VIHALS sideboard have?

It has two bays separated by a central partition, with one adjustable shelf (max load 18 kg) on four pins (10051660) in each bay, two full-width drawers at the top, and four doors below—two hinged on the outer side panels and two hinged on the central partition.

Safety

This sideboard must be anchored to the wall with the enclosed wall brackets, using screws and plugs that suit your wall, so it cannot tip over when the drawers and doors are opened.

About this guide

This is an independent 3D engineering guide modeled from physical hardware specifications and standard fastener part numbers so you can identify your pieces before building. The outer size, 140 × 37 × 75 cm, is IKEA's published size. The outer size and max. shelf load are IKEA’s. Board thicknesses, drawer sizes and hole positions are our own estimates. The 3D runs faster than real hands do.

IKEA gives a max. load of 18 kg per shelf for this sideboard.

The manufacturer's instructions are on IKEA's product page (PDF). If something here differs from the manual in your box, follow the manual.

The 3D models, drawings and text are our own. IKEA and VIHALS are named only to say which product this guide is for.