Step 2 of 18
OMAR 92×36×181 step 2 of 18: Clip on the bottom clips
Clip a shelf clip round each post at the groove a little way up from the foot: two halves (130531), one from each side, pressed together round the post until they lock, narrow end towards the top of the post. Put them at the same groove on all 4 posts.
- 8× Shelf clip half
130531
Tools: none, just your hands
- Both halves go in the same groove and the same way up: the manual crosses out a clip put on wrongly.
All 18 steps
- 1 Screw the feet into the posts
- 2 Clip on the bottom clips
- 3 Push two posts through the first shelf common mistake
- 4 Push the other two posts through
- 5 Stand it up and clip on the middle clips
- 6 Lower the middle shelf onto the clips
- 7 Clip on the top clips
- 8 Lower the top shelf onto the clips
- 9 Press the caps into the posts
- 10 Second unit: the feet and the bottom clips
- 11 Second unit: the first shelf and its posts
- 12 Second unit: stand it up, the middle shelf
- 13 Second unit: the top shelf and the caps
- 14 Stand the first unit at the wall, caps off
- 15 Take the sleeves off the second unit
- 16 Lift the second unit on top
- 17 Clip on the wall fittings
- 18 Screw the fittings to the wall common mistake
00Overall
The outer size is IKEA's published size.
01Elevations
Drawn from our 3D model, to scale. Point at a part to find it in the list below; click it to jump there.
02Parts / cut list
| Part | Name | Qty | T | W | L | Material |
|---|---|---|---|---|---|---|
| A | PostA galvanised steel post, grooved all along, so the shelf clips can go at any height. The foot screws into the sleeve on its bottom end, and its open top takes a cap, or the next unit’s post.25 × 25 × 926 mm | ×8 | 25 mm | 25 mm | 926 mm | Steel, galvanized |
| B | Shelf42 × 360 × 920 mm | ×6 | 42 mm | 360 mm | 920 mm | Steel, galvanized |
The parts' sizes are our 3D model's own estimates: close, not measured. The outer sizes (92 × 36 × 94 cm a unit, 181 cm stacked), the shelves’ 33 kg load, the boxes’ weights and the hardware’s sizes and materials are IKEA’s; the posts’ grooves and sleeves, the shelves’ wires and heights and where the wall fittings sit are our own estimates. IKEA publishes only the outer size.
03Tools & materials
| Tools | ||
|---|---|---|
| Flat screwdriverDrives the 4 wall screws through the wall fittings: one that suits your screws. | You need it | |
| Materials | ||
| Steel, galvanized | AB | |
Not in the box: 4 wall screws and 4 wall plugs that suit your wall.
04Hardware
| ×8 | Adjustable footprinted with 10055938, the same foot in another colour | 139294 | M8 × 30 mm thread, foot ø24 × 13 mm | Galvanized steel and black polyamide plastic |
| ×48 | Shelf clip halfprinted with 10055941, the same clip in another colour | 130531 | For a ø25 mm post | Black ABS plastic |
| ×8 | Cover capprinted with 10055957, the same cap in green | 139285 | ø25 mm | Black polypropylene |
| ×4 | Wall fittingprinted with 10056017, the same fitting in another colour | 10054272 | 53 × 22 × 38 mm, for a ø25.4 mm post | Black polyamide plastic |
| ×4 | Spacerprinted with 10056003, the same spacer in another colour | 10054270 | 30 × 23 × 16 mm | Black polyamide plastic |
Questions
How do you stack two OMAR shelving units?
Build both units the same way. Pull the 4 caps out of the tops of the lower unit’s posts, pull the sleeves, with their feet, off the bottom ends of the upper unit’s posts, then lift the upper unit on so the narrow ends of its posts go into the lower unit’s posts. IKEA shows no more than two units stacked.
Which way up do the OMAR shelves go?
The wire ends bend down at the front and back of each shelf: that is its underside. While the first shelf stands on its edge for the posts, its underside faces the feet; the other two go on the right way up, lowered over the posts.
Do I need tools to assemble OMAR?
No tools for the shelving itself: the feet, clips, shelves and caps all go on by hand. For the wall fittings you need a screwdriver for your wall screws, and screws and plugs that suit your wall, which are not in the box.
Do I have to fix the OMAR section to the wall?
Yes. IKEA says it must be securely anchored: each box has two wall fittings, which clip round the back posts under the top shelf, and two spacers for a skirting board.
How much can each OMAR shelf hold?
IKEA gives a maximum load of 33 kg for each shelf.
Safety
Furniture that tips over can cause serious or fatal crushing injuries. IKEA says this shelving must be securely anchored to the wall with the wall fittings in the box. Wall screws and plugs are not included: use ones that suit your wall, and ask a professional if you are unsure. Stack no more than two units, and use it only indoors.
About this guide
This is an independent 3D engineering guide modeled from physical hardware specifications and standard fastener part numbers so you can identify your pieces before building. The outer size, 92 × 36 × 181 cm, is IKEA's published size. The outer sizes (92 × 36 × 94 cm a unit, 181 cm stacked), the shelves’ 33 kg load, the boxes’ weights and the hardware’s sizes and materials are IKEA’s; the posts’ grooves and sleeves, the shelves’ wires and heights and where the wall fittings sit are our own estimates. The 3D runs faster than real hands do.
IKEA gives a maximum load of 33 kg for each shelf. Only for indoor use.
The manufacturer's instructions are on IKEA's product page (PDF). If something here differs from the manual in your box, follow the manual.
The 3D models, drawings and text are our own. IKEA and OMAR are named only to say which product this guide is for.