Step 5 of 6
BROR work bench 110×55 step 5 of 6: Fit the lower shelf
Lower the second steel shelf upside down between the 4 posts, skipping one pair of holes so it sits at the fourth pair of holes from the worktop (one pair of holes down from the feet). Hold a corner bracket (10050776) inside each corner and drive 2 screws (10042206) at all four corners with the hex key.
Tools: Hex key (100092, in the box)
All 6 steps
00Overall
The outer size is IKEA's published size.
01Elevations
Drawn from our 3D model, to scale. Point at a part to find it in the list below; click it to jump there.
02Parts / cut list
| Part | Name | Qty | T | W | L | Material |
|---|---|---|---|---|---|---|
| A | WorktopA thick pine plywood board factory-fitted to a folded black steel rim. The work bench is built upside down on it so the wood stays clean on the rug.50 × 550 × 1100 mm | ×1 | 50 mm | 550 mm | 1100 mm | Pine plywood; steel rim with epoxy/polyester powder coating |
| B | PostAn L-shaped powder-coated steel post with five pairs of holes for setting the shelves at different heights. Its square-cut bottom end takes the plastic foot in step 1; its rounded top end meets the worktop.38 × 38 × 880 mm | ×4 | 38 mm | 38 mm | 880 mm | Steel, epoxy/polyester powder coating |
| C | Shelf40 × 550 × 1100 mm | ×2 | 40 mm | 550 mm | 1100 mm | Steel, epoxy/polyester powder coating |
The parts' sizes are our 3D model's own estimates: close, not measured. Outer size (110 × 55 × 88 cm), shelf spacings (20 and 40 cm), package weight (24.5 kg) and hardware sizes come from IKEA’s product and spare-parts data; sheet-metal thickness and flange widths are read from the assembly drawings. IKEA publishes only the outer size.
03Tools & materials
| Tools | ||
|---|---|---|
| Hex keyComes in the box. Starts all 24 M6 screws in steps 2 to 5, then tightens them once the work bench is standing straight in step 6. | In the box 100092 · 4 mm | |
| Spirit levelHeld upright against the side of the work bench in step 6 while you press the frame square before tightening the screws. | You need it | |
| Materials | ||
| Pine plywood; steel rim with epoxy/polyester powder coating | A | |
| Steel, epoxy/polyester powder coating | BC | |
Questions
Which end of the BROR posts do the plastic feet go on?
Each L-shaped post has one end with rounded corners and a pair of screw holes close to the edge, and one square-cut end. Push the plastic feet (192249) onto the square-cut bottom ends in step 1, and put the rounded ends against the worktop in steps 2 and 3.
Why should I wait until the end to tighten the 24 screws fully?
Starting the screws slightly loose lets both steel shelves slip easily between the four posts and lets you press the standing frame plumb against a spirit level in step 6 before locking the 12 corner brackets rigid.
Can I set the two steel shelves at different heights?
Yes. Each post has five pairs of screw holes spaced 20 cm apart. The top pair holds the worktop, and you can bolt the two steel shelves into any of the four lower pairs of holes to suit what you store.
What tools do I need to assemble the BROR work bench?
Only the 4 mm hex key (100092) included in the box and a spirit level to check that the posts stand vertical before your final tightening. You do not need a screwdriver.
Safety
Only for indoor use. Check the screws regularly and re-tighten them when necessary so the frame stays rigid under load.
About this guide
This is an independent 3D engineering guide modeled from physical hardware specifications and standard fastener part numbers so you can identify your pieces before building. The outer size, 110 × 55 × 88 cm, is IKEA's published size. Outer size (110 × 55 × 88 cm), shelf spacings (20 and 40 cm), package weight (24.5 kg) and hardware sizes come from IKEA’s product and spare-parts data; sheet-metal thickness and flange widths are read from the assembly drawings. The 3D runs faster than real hands do.
Holds up to 60 kg, according to IKEA, and is tested for public use (EN 16121). Only for indoor use.
The manufacturer's instructions are on IKEA's product page (PDF). If something here differs from the manual in your box, follow the manual.
The 3D models, drawings and text are our own. IKEA and BROR are named only to say which product this guide is for.