iFlatpack.com is an independent platform creating original 3D procedural instructions. We are not affiliated with, endorsed by, or sponsored by Inter IKEA Systems B.V. or any other brand mentioned. All product names and part numbers are used strictly for identification and compatibility purposes.

Step 27 of 35 · IKEA manual page 35

MICKE desk step 27 of 35: Lock the top

Put a cam lock (110126) into each of the 6 round holes just under the top, arrow to the bolt, and turn each clockwise until it is tight.

6× Cam lock 110126

Tools: Flat screwdriver

All 35 steps

Parts and hardware checklist

1×	Back rail	about 69.5×18×1.6 cm
1×	Cable shelf	about 69.5×7.4×1.6 cm
1×	Cable channel front	about 69.5×5×1.6 cm
1×	Supporting leg	about 50×18×3 cm
2×	Cabinet side	about 71×50×3 cm
1×	Cabinet bottom	about 50×26.5×2.5 cm
1×	Fixed shelf	about 48×26.5×1.6 cm
1×	Metal frame	about 53.7×50×3 cm
1×	Top	about 105×50×3 cm
1×	Door	about 56.2×26.1×1.6 cm
2×	Shelf	about 44×26.3×1.6 cm
1×	Drawer front	about 69.1×9.4×1.6 cm
4×	Drawer side	about 36×6.5×1.2 cm
1×	Drawer bottom	about 65.4×34.8×0.3 cm
1×	Drawer back	about 64.6×5.3×1.2 cm
1×	Drawer front	about 26.1×9.4×1.6 cm
1×	Drawer bottom	about 34.8×22.4×0.3 cm
1×	Drawer back	about 21.6×5.3×1.2 cm
22×	Cam bolt	`#118331` · 41 mm long
20×	Dowel	`#101344`
4×	Cam lock	`#103114`
8×	Cam lock	`#103430`
10×	Cam lock	`#110126`
4×	Plastic fastener	`#110519`
8×	Drawer runner	`#112482` two sets, each four halves: two on the desk and two on the drawer
20×	Screw	`#100365`
2×	Mounting plate	`#109221`
4×	Screw	`#113287`
3×	Long screw	`#100086`
4×	Glide	`#153549`
2×	Felt pad	`#10081375`
8×	Shelf pin	`#101514`
2×	Hinge	`#109338`
2×	Bumper	`#104663`
2×	Bumper pad	`#112519`
1×	Cable outlet	`#121304`

Tools you need

Hammer · Taps in the drawers’ four plastic fasteners.
Cross-head screwdriver · Screws in the cam bolts and the screws for the runners, the mounting plates and the hinges, and turns the drawers’ cam locks.
Flat screwdriver · Turns the desk’s 18 cam locks.

Questions

Can the MICKE desk’s cabinet go on the left?

Yes. The manual draws both: pages 10 to 24 build it with the cabinet on the left and the metal frame on the right, pages 25 to 39 the other way round, as this guide does.

Which cam lock goes where?

MICKE has three kinds. 103114 goes in the drawers, 103430 in the cable channel’s boards, and 110126 in the cabinet’s bottom and under the top. Each step of the manual shows the right one with the others crossed out.

Why is the desk built lying on its back?

So the boards can be stood on their edges and locked on the floor. It is stood up only when the top and the frame are on, before the drawers and the door go in.

What tools do I need?

A cross-head screwdriver, a flat screwdriver and a hammer, as the manual shows. The hex key and its handle for the frame’s screws are in the box.

How much can the MICKE desk hold?

IKEA gives 50 kg for the desk and 8 kg for each shelf.

Safety

undefined

About this guide

The steps, the part numbers, the counts and the order come from IKEA's assembly manual AA-476615-12 (2024-04-30). The outer size, 105 × 50 × 75 cm, is IKEA's published size. The overall size is IKEA’s; the boards’ thicknesses, the cabinet’s width and the hole positions are read off the manual’s drawings, so they are close, not measured. The 3D runs faster than real hands do.

IKEA gives the desk’s maximum load as 50 kg, and 8 kg for each shelf.

The manufacturer's instructions are on IKEA's product page (PDF). If something here differs from the manual in your box, follow the manual.

The 3D models, drawings and text are our own. IKEA and MICKE are named only to say which product this guide is for.