iFlatpack.com is an independent platform creating original 3D procedural instructions. We are not affiliated with, endorsed by, or sponsored by Inter IKEA Systems B.V. or any other brand mentioned. All product names and part numbers are used strictly for identification and compatibility purposes.

Step 10 of 19 · IKEA manual page 16

KALLAX 77×147 step 10 of 19: Dowels for the last divider

Tap 4 dowels into the holes in the middle of the other face of the third long shelf.

4× Dowel 101339

Tools: Hammer

All 19 steps

Parts and hardware checklist

1×	Top board	about 76.5×39×3.8 cm
2×	Side board	about 138.9×39×3.8 cm
4×	Short divider	about 39×33.5×1.6 cm
3×	Long shelf	about 68.9×39×1.6 cm
1×	Bottom board	about 76.5×39×3.8 cm
8×	Long screw	`#104321` · 70 × 6 mm printed as 104321 or 104322
44×	Dowel	`#101339` · 6 × 50 mm
4×	Short screw	`#100372` · 17 × 5 mm
8×	Glide	`#153550` · 25 mm across 4 when it stands upright, all 8 when it lies on its long side
2×	Wall bracket	`#115753` · 56 × 42 mm, 36 mm flange
2×	Wall fitting	`#103693` · 34 × 26 mm
2×	Bracket cover	`#115754` the number depends on the colour: 115754, 118673, 118225, 119509, 118814, 121184 or 123773
1×	Hex key	`#100001`

Tools you need

Spirit level · Held upright against the outside of a side, to check that the unit stands straight before you mark the wall.
Hammer · Taps all 44 dowels into their holes: straight, and only halfway in.
Cross-head screwdriver · Drives the 4 short screws that hold the wall brackets.
Flat screwdriver · Drives the 2 wall screws, then tightens them through the wall fittings.
Pencil · Marks the wall through the round hole in each bracket, where the wall screws go.

Not in the box: 2 wall screws and 2 wall plugs that suit your wall.

Questions

How many dowels does the KALLAX 77×147 use?

Forty-four wooden dowels, part 101339, 6 × 50 mm: four at every joint of the shelves and dividers. Each goes halfway into one board and halfway into the next.

Why are there 8 glides when it only needs 4?

Standing upright, as this guide builds it, it stands on 4 glides under the bottom board. Lying on its long side, as the manual also shows, it uses all 8.

Which way round do the side boards go?

Each long side has two small holes near one long edge, at both ends. That edge goes at the back, at the bottom while you build, so the wall bracket can be screwed into them in step 16.

Do I have to fix KALLAX to the wall?

Yes. IKEA says it must be fixed to the wall with the two brackets in the box, so it cannot tip over. The wall screws and plugs are not included: use ones that suit your wall.

What tools do I need?

A hammer for the dowels, a cross-head screwdriver for the bracket screws, a flat screwdriver for the wall screws, a pencil and a spirit level. The hex key for the long screws is in the box.

Safety

Furniture that tips over can cause serious or fatal crushing injuries. IKEA says this unit must be fixed to the wall with the brackets in the box. Wall screws and plugs are not included: use ones that suit your wall, and ask a professional if you are not sure.

About this guide

The steps, the part numbers, the counts and the order come from IKEA's assembly manual AA-2703471-1 (2026-03-09). The outer size, 76.5 × 39 × 146.5 cm, is IKEA's published size. Board thickness, hole positions and the bracket height are read off the drawings, so they are close, not measured. The 3D runs faster than real hands do.

Each shelf holds up to 13 kg, according to IKEA.

The manufacturer's instructions are on IKEA's product page (PDF). If something here differs from the manual in your box, follow the manual.

The 3D models, drawings and text are our own. IKEA and KALLAX are named only to say which product this guide is for.