Step 4 of 7
INGATORP table step 4 of 7: Fit the crossbars and screw in the cam bolts
Place the left and right solid birch crossbars across the outer ends of the cross mounting plate, then drive 4 cam bolts (118331) with a Phillips screwdriver into the front and back ends of both crossbars.
- 2× Slide frame crossbar
- 4× Cam bolt
118331
Tools: Phillips screwdriver
All 7 steps
- 1 Push eight dowels into the pedestal base
- 2 Bolt the four curved legs to the pedestal common mistake
- 3 Screw the cross mounting plate to the column
- 4 Fit the crossbars and screw in the cam bolts
- 5 Lock on the extension slide rails
- 6 Fasten the two semi-circular tabletop halves
- 7 Fit the leaf pins and unfold the butterfly leaf
00Overall
The outer size is IKEA's published size, the height as far as it adjusts.
01Elevations
Drawn from our 3D model, to scale. Point at a part to find it in the list below; click it to jump there.
02Parts / cut list
| Part | Name | Qty | T | W | L | Material |
|---|---|---|---|---|---|---|
| A | Turned pedestal columnTurned central baluster column with a square lower block where the four splayed legs attach and a wide top flange that supports the upper cross mounting plate.180 × 180 × 556 mm | ×1 | 180 mm | 180 mm | 556 mm | Solid birch and high-density fibreboard, white acrylic finish |
| B | Curved splayed leg70 × 250 × 300 mm | ×4 | 70 mm | 250 mm | 300 mm | Solid birch, white acrylic paint |
| C | Upper cross mounting plateWide mounting plate bolted to the top of the pedestal column to carry the wooden extension slide frame.28 × 400 × 560 mm | ×1 | 28 mm | 400 mm | 560 mm | Solid birch and birch plywood, white finish |
| D | Slide frame crossbar40 × 50 × 320 mm | ×2 | 40 mm | 50 mm | 320 mm | Solid birch |
| E | Extension slide rail40 × 50 × 920 mm | ×2 | 40 mm | 50 mm | 920 mm | Solid birch glider rail |
| F | Semi-circular tabletop half26 × 550 × 870 mm | ×2 | 26 mm | 550 mm | 870 mm | Particleboard and fibreboard with ABS edge banding and white acrylic finish |
| G | Folding butterfly extension leaf45 cm folding butterfly extension leaf hinged across its middle so it folds in half to store inside the frame when the table is closed to 110 cm.26 × 450 × 870 mm | ×1 | 26 mm | 450 mm | 870 mm | Particleboard and fibreboard, white acrylic finish, brass center hinges |
The parts' sizes are our 3D model's own estimates: close, not measured. The turned profile of the central pedestal, the curve of the four splayed legs and the hole positions along the extension slide rails are our own estimates from IKEA’s manual and product measurements. IKEA publishes only the outer size.
03Tools & materials
| Tools | ||
|---|---|---|
| Hex keyA 4 mm L-shaped hex key included in the hardware bag. It drives the 4 leg bolts (122606) and the 12 wood screws (100214) that secure the cross plate, extension rails and tabletop halves. | In the box 100001 | |
| Box spannerTubular socket spanner with a tommy bar included in the box for tightening the 4 leg nuts (100712) onto the lower leg studs. | In the box 120202 | |
| Phillips screwdriverDrives the 4 cam bolts (118331) into the ends of the extension frame crossbars. | You need it | |
| Flathead screwdriverTurns the 4 cam locks (119081) half a turn clockwise to lock the outer slide rails to the crossbars. | You need it | |
| Materials | ||
| Solid birch and high-density fibreboard, white acrylic finish | A | |
| Solid birch, white acrylic paint | B | |
| Solid birch and birch plywood, white finish | C | |
| Solid birch | D | |
| Solid birch glider rail | E | |
| Particleboard and fibreboard with ABS edge banding and white acrylic finish | F | |
| Particleboard and fibreboard, white acrylic finish, brass center hinges | G | |
Not in the box: Phillips screwdriver, Flathead screwdriver.
Questions
What tools do I need to assemble the IKEA INGATORP extendable table?
The 4 mm hex key (100001) and the box spanner (120202) are included in the hardware bag. You only need to bring a Phillips screwdriver for the 4 cam bolts (118331) and a flathead screwdriver for the 4 cam locks (119081).
How does the butterfly extension leaf store inside the INGATORP table?
When you pull the two semi-circular tabletop halves apart along the birch glider rails, the 45 cm butterfly leaf unfolds flat to extend the table from 110 cm to 155 cm, or folds in half on its brass centre hinges to stow neatly under the tabletop between the slide rails.
Why does the INGATORP pedestal base feel slightly loose after a few weeks?
Natural solid birch settles slightly under load during the first weeks of use. Reach around the lower pedestal block with the included box spanner (120202) and hex key (100001) to re-tighten the 4 leg nuts (100712) and 4 leg bolts (122606).
How many people does the INGATORP 110/155 cm extendable table seat?
Closed to its 110 cm round diameter, the INGATORP table comfortably seats 4 people; extended to 155 × 87 cm with the butterfly leaf unfolded, it seats up to 6 people.
Safety
Two people are needed to lift and turn the assembled table safely, and keep fingers clear of the folding butterfly leaf hinges when opening or closing the extension leaf.
About this guide
The part numbers and counts match IKEA's assembly instructions, so you can check each piece against your box. The outer size, 110–155 × 87 × 74 cm, is IKEA's published size. The turned profile of the central pedestal, the curve of the four splayed legs and the hole positions along the extension slide rails are our own estimates from IKEA’s manual and product measurements. The 3D runs faster than real hands do.
Seats 4 people at its 110 cm round size and extends to 155 cm with the self-storing butterfly leaf to seat 6.
The manufacturer's instructions are on IKEA's product page (PDF). If something here differs from the manual in your box, follow the manual.
The 3D models, drawings and text are our own. IKEA and INGATORP are named only to say which product this guide is for.