Step 3 of 7
IDÅSEN desk step 3 of 7: Join and set the telescoping crossbeam
Slide the right crossbeam tube inside the left crossbeam section, set the assembly across the tops of both lifting columns at the 120 cm width mark, and drive the eight countersunk bolts (110907) with the hex key (100001) to secure the ends and lock the overlap.
- 1× Left crossbeam section
- 1× Right crossbeam section
- 8× Countersunk bolt
110907
Tools: Hex key (100001, in the box)
All 7 steps
- 1 Fit the four levelling glides to the feet
- 2 Bolt the lifting columns to the feet
- 3 Join and set the telescoping crossbeam
- 4 Attach the left and right top brackets
- 5 Mount the stained ash veneer tabletop common mistake
- 6 Fit the power unit, cable net, and controller
- 7 Calibrate and raise to standing height
00Overall
The outer size is IKEA's published size, the height as far as it adjusts.
01Elevations
Drawn from our 3D model, to scale. Point at a part to find it in the list below; click it to jump there.
02Parts / cut list
| Part | Name | Qty | T | W | L | Material |
|---|---|---|---|---|---|---|
| A | Left floor foot60 × 80 × 620 mm | ×1 | 60 mm | 80 mm | 620 mm | — |
| B | Right floor foot60 × 80 × 620 mm | ×1 | 60 mm | 80 mm | 620 mm | — |
| C | Left lifting column80 × 480 × 480 mm | ×1 | 80 mm | 480 mm | 480 mm | — |
| D | Right lifting column80 × 480 × 480 mm | ×1 | 80 mm | 480 mm | 480 mm | — |
| E | Left crossbeam section38 × 110 × 555 mm | ×1 | 38 mm | 110 mm | 555 mm | — |
| F | Right crossbeam section38 × 102 × 555 mm | ×1 | 38 mm | 102 mm | 555 mm | — |
| G | Left top support bracket20 × 70 × 560 mm | ×1 | 20 mm | 70 mm | 560 mm | — |
| H | Right top support bracket20 × 70 × 560 mm | ×1 | 20 mm | 70 mm | 560 mm | — |
| J | Tabletop25 × 700 × 1200 mm | ×1 | 25 mm | 700 mm | 1200 mm | — |
| K | Power supply unit30 × 80 × 200 mm | ×1 | 30 mm | 80 mm | 200 mm | — |
| L | Cable management net80 × 220 × 800 mm | ×1 | 80 mm | 220 mm | 800 mm | — |
| M | Height adjustment controller20 × 62 × 80 mm | ×1 | 20 mm | 62 mm | 80 mm | — |
The parts' sizes are our 3D model's own estimates: close, not measured. IKEA publishes only the outer size.
Questions
How do I reset or calibrate the IDÅSEN sit/stand desk?
Press and hold the front paddle controller downward for at least five seconds at the lowest 63 cm stop until both columns pulse slightly. That synchronizes the left and right motors.
Which width setting should the telescoping crossbeam use?
Align the telescoping crossbeam with the 120 cm inner width marks before tightening the four centre clamping bolts (110907); the wider 160 cm marks are for the 160×80 cm tabletop.
Safety
Keep clear of the gap around the tabletop while raising or lowering the desk, and always complete the five-second downward paddle reset before first use so both motorized columns stay synchronized.
About this guide
The part numbers and counts match IKEA's assembly instructions, so you can check each piece against your box. The outer size, 120 × 70 × 63–127 cm, is IKEA's published size. The 3D runs faster than real hands do.
The manufacturer's instructions are on IKEA's product page (PDF). If something here differs from the manual in your box, follow the manual.
The 3D models, drawings and text are our own. IKEA and IDÅSEN are named only to say which product this guide is for.