Step by step HEMNESday-bed
Step15/44
Hardware in0/311
Parts in0/60
Open IKEA PDF ↗
Screw the cam bolts into the front boardstep 15 of 44 · manual page 14

iFlatpack.com is an independent platform creating original 3D procedural instructions. We are not affiliated with, endorsed by, or sponsored by Inter IKEA Systems B.V. or any other brand mentioned. All product names and part numbers are used strictly for identification and compatibility purposes.

Step 15 of 44 · IKEA manual page 14

HEMNES day-bed step 15 of 44: Screw the cam bolts into the front board

Screw 8 cam bolts (118331) into the front board.

Tools: Cross-head screwdriver

All 44 steps

  1. 1Screw the castors under the rails
  2. 2Screw on the runners marked CR
  3. 3Screw on the runners marked CL
  4. 4Push the dowels into the rails
  5. 5Lay the slat holder on the long board
  6. 6Screw the slat holder down
  7. 7Screw the cam bolts into the long board
  8. 8Stand the rails on the long board
  9. 9Lock the rails to the long board
  10. 10Push the dowels into the end boards
  11. 11Stand the end boards on the long board
  12. 12Lock the end boards
  13. 13Lay the slat holder on the front board
  14. 14Screw the slat holder down
  15. 15Screw the cam bolts into the front board
  16. 16Lay the front board on top
  17. 17Lock the end boards to the front board
  18. 18Lock the rails to the front board
  19. 19Screw in three short slats
  20. 20Push the pins into the other slats
  21. 21Turn the base over and lay on the slats common mistake
  22. 22Lay the slat holder on the back panel
  23. 23Screw the slat holder down
  24. 24Push the dowels into the ends
  25. 25Bolt the ends to the back panel
  26. 26Press the feet into the legs
  27. 27Screw on the front rail
  28. 28Turn it over and fit the stop plates
  29. 29Screw the side rails in
  30. 30Push a pin into each slat
  31. 31Lay the slats on and screw them down
  32. 32Push the base in
  33. 33Tap in the studs
  34. 34Press on the top rail
  35. 35Press on the arm caps
  36. 36Drawers: screw in the cam bolts
  37. 37Drawers: stand the sides on the fronts
  38. 38Drawers: lock the sides to the fronts
  39. 39Drawers: slide in the bottoms
  40. 40Drawers: put on the backs
  41. 41Drawers: lock the backs
  42. 42Drawers: screw on the runners
  43. 43Drawers: fit the knobs
  44. 44Slide the drawers in

Parts and hardware checklist

1×Back panelabout 201×58×1.8 cm
1×Left endabout 89×80×4 cm
1×Right endabout 89×80×4 cm
1×Slat holder 112975about 199×3×3 cm
1×Front rail 112977about 201×3×2 cm
2×Side railabout 82.1×4.8×1.8 cm
12×Slatabout 81.5×6.8×1.8 cm
1×Top railabout 200.4×4.5×3 cm
2×Arm capabout 90×4.6×3 cm
1×Long boardabout 199×30×1.8 cm
2×Slat holder 112975about 195×2.5×2 cm
1×Front boardabout 199×33.2×1.8 cm
4×Railabout 76.4×8×4 cm
2×End boardabout 76.4×30×1.8 cm
13×Slatabout 76×6.8×1.8 cm
3×Drawer frontabout 58.2×22.2×1.8 cm
6×Drawer sideabout 70×21.6×1.2 cm
3×Drawer bottomabout 69.6×55.8×0.3 cm
3×Drawer backabout 57.4×21.6×1.2 cm
8×Castor#111401
16×Screw#109049
12×Drawer runner#139505 three sets of four: CR and CL for the base, DR and DL for the drawers
36×Screw#100347
34×Dowel#101350 · 30 mm long
40×Cam bolt#118331 · 41 mm long
16×Cam lock#103430
50×Screw#116894
32×Slat pin#110525
4×Long bolt#105236
4×Barrel nut#108903
1×Hex key#100001
4×Screw#109060
2×Clip#130485
4×Foot#153552
2×Stop plate#123660
17×Stud#104012
24×Cam lock#103114
3×Knob#117615
3×Knob bolt#119976

Tools you need

Not in the box: Two mattresses, 80 × 200 cm.

Questions

How do I tell the slats apart?

There are 13 short slats for the pull-out base, 12 long ones for the bed and 2 narrow side rails. The manual shows each set with the other crossed out: if a slat does not drop in between the slat holders, it is the wrong length.

Why does the frame have to be lifted to push the base in?

The stop plates on the front ends of the side rails hang down inside the base, behind its front board. Lift the front of the frame a little so they clear the base, push it in, and let the frame down.

How does it become a double bed?

Pull the base out: IKEA says it then makes a 160 × 200 cm bed with two 80 × 200 mattresses. It is not to be used as two single beds.

What tools do I need?

A flat screwdriver for the cam locks, a cross-head screwdriver for the screws and cam bolts, and a hammer for the studs, as the manual shows. The hex key for the long bolts is in the box.

Which screws go where?

The short 100347 screws are for the runners only; the 116894 screws hold the slat holders, the stop plates, the side rails and the slats; the 109060 screws hold the front rail. Each page shows the one to use with the other crossed out.

Safety

From the manual: never stand on an open drawer, and do not sit on the frame before the base is in. Stand the whole day-bed on a rug or off it, not half on. IKEA says it is not to be used as two single beds; re-tighten the screws and fittings when needed.

About this guide

The steps, the part numbers, the counts and the order come from IKEA's assembly manual AA-1913852-7 (2018-07-12). The outer size, 209 × 89 × 83 cm, is IKEA's published size. The day-bed’s size and the drawers’ insides are IKEA’s; the boards’ thickness, the rails, the slats and where the holes are, are read off the manual’s drawings, so they are close, not measured. The 3D runs faster than real hands do.

IKEA says it takes two 80 × 200 cm mattresses; pulled out it is a 160 × 200 cm double bed, and it is not to be used as two single beds. The drawers are 55 × 70 × 20 cm inside.

The manufacturer's instructions are on IKEA's product page (PDF). If something here differs from the manual in your box, follow the manual.

The 3D models, drawings and text are our own. IKEA and HEMNES are named only to say which product this guide is for.